Other translations include lavender, as used by Edward Seidensticker in his English version of Genji violet and violet root, which in Japanese poetry denotes love and constancy. Murasaki ( 紫) is the Japanese word for the color purple. How glad I would be to pick and soon to make mine that little wild plant sprung up from the very root shared by the murasaki. The name Murasaki is inspired by a poem that the novel's hero, Genji, improvises when contemplating his first meeting with the novel's heroine, the little girl who will grow up to be "Murasaki": In most commentaries and translations, she is simply referred to as "Murasaki" for ease of identification and to improve readability. As such, the Genji character Murasaki is often referred to as the "Lady of the West Wing". The name is a pseudonym, as due to court manners of the time (the Heian period, 794–1185), it was considered unacceptably familiar and vulgar to freely address people by either their personal or family names within the novel, the character is unnamed, and most of the book's characters are never identified by name, but by their rank and title (in the case of male persons), the rank and title of their male relatives (in the case of female persons), or after the name of their habitation (in the case of the great court ladies). Then I had error massage.(I miss screenshot).Murasaki refers to the heroine of The Tale of Genji ( Genji Monogatari), after whom the book's author, Murasaki Shikibu, is known. Then type $ make -f hello.ftdi.44.echo.c.make. I downloaded "hello.ftdi.44.echo.c" and "hello.ftdi.44.echo.c.make"and put to into same folder. Next I tried to write "hallo echo.c" by terminal, but fail. I soldered the resistance again and tried it again. And in that state I was connected to the PC. I misplaced the position of the resistance several times and redoed soldering, so I forgot to put resistance in one place. It maybe broke.)Then green light shone.Īttention point is pin correspondence between pin header and FTDI.GND to GND,CTS to CTS.I could confirm it by my board image of eagle, but it is not useful, so next time I want to write pin name to on board(now I wrote it back of board by hands).
Murasaki effect serial#
Then I connected it to may computer by AVR markⅡ and FTDI serial connection module MM-FT232.(My Fab isp can not be used. I test my board by a digital multimeter to find short and confirm connection. Īttention point is direction of LED and button. I think I got used to soldering a bit and this board layout is good for beginner. Then I change "drill diameter" setting to 0.4 (drill remains 0.7mm).And I used 1.0mm drill for interior. I used 0.7mm drill, so I set fab module's drill diameter 0.7, but it is too big so details can not be milled. Do not change window size since when we exported trace! select layer only No.20.Then export. adjust the window to fit out line(interior) > select layers only No.1,16,17,18Įxport > image > check monochrome >set dpi 500 >set size "window">OKĪt last, export interior. It need margin over 2.6 mm, over 3.8mm is safe to mill (When I use 1.0mm drill for cut outline).Īlso we cn use autoroute tool.(this time I did not use) I connected these components mamnualy without cross lines by route tool.
I moved and rotate each components to proper place. In order to make margin I used 0ohm resistor as jumper and I escaped the line outside. I am not good at soldering, and I heard it is difficult to mill thick line by our lab milling machine, so I made my board layout with margin. It is not to simulate (values do not effect to anything),but to understand which symbol is which component when we look board window. The same name line will connect.Īt last,I added names and values. For example, attiny's No.3 pin and No.2 pin is XTAL, so I connect it to resonaator (crystal).Īnd We can connect with name. Next, I connected with line(NET).By Click net button and draw line to device foot from another device foot. So I rotated resonator synbol like below image. In shematics, GND should be written at bottom.
I added devices and symbols(like GND and vcc).click add button > choose component > rotate (right click) > put it (left click)Īnd we can also ratate by rotate tool.As per the resonators datasheet, resonator's No.2 pin is GND. This is first time to draw schematic, so I reference fabAcademy tutorial. I add only one LED(and resistor) and one button. Electronic design Learn basic electronic rules
0 kommentar(er)
